错误代码： 13.B9.Az | 惠普5系激光打印机 故障代码 其他系列也可以参考 | 二〇二一年五月二十七日
2021-06-01
错误代码： 13.B9.Az | 惠普5系激光打印机 故障代码 其他系列也可以参考 |
二〇二一年五月二十七日
--------------------------------------------------
技术热线：朱师傅整理
--------------------------------------------------
中文译本：
13.B9.Az定影器卡纸
描述
定影器交货期。
介质卡在定影器区域。
在指定的时间限制后，纸张出现在SR9。
此果酱代码可能是由以下原因引起的：
定影器出口处出现手风琴卡纸，在输出辊之前堵塞了介质。出纸槽
滚筒不转动，与热凝器出口和接纸架之间的距离很小。
粘性的定影器出口标志，如果其在启动位置暂时卡住甚至延迟。
●13.B9.A1
从纸盘1打印时检测到重张进纸卡纸。
●13.B9.A2
从纸盘2打印时检测到重张进纸卡纸。
●13.B9.A3
从纸盘3打印时检测到重张进纸卡纸。
●13.B9.A4
ZHCN故障排除工具227
从纸盘4打印时，检测到多页进纸卡纸。
●13.B9.AD
从双面打印器打印时，检测到重张进纸卡纸。
建议操作
小心：请小心热熔器是热的，如果需要清除热熔器内部和周围的碎屑，请使其冷却。
压力加热组件。
1.打开右上门，然后清除所有卡纸。
2.确保纸张符合HP打印机规格。
3.检查定影器送纸传感器的功能和运动是否正常。
4.确认之前没有卡在定影器中的碎屑或引入或流出定影器的辊子没有碎屑。
5.确认出纸槽辊正在转动。
6.卸下ITB并检查是否有损坏和碎屑。
7.进行Manuel传感器测试，并检查SR9定影器输送传感器。如果发现故障，则更换定影器
集会。
8.进行Manuel传感器测试并更换定影组件。
9.更换热凝器。
描述
定影器交货期。
介质卡在定影器区域。
在指定的时间限制后，纸张出现在SR9。
此果酱代码可能是由以下原因引起的：
定影器出口处出现手风琴卡纸，在输出辊之前堵塞了介质。出纸槽
滚筒不转动，与热凝器出口和接纸架之间的距离很小。
粘性的定影器出口标志，如果其在启动位置暂时卡住甚至延迟。
●13.B9.A1
从纸盘1打印时检测到重张进纸卡纸。
●13.B9.A2
从纸盘2打印时检测到重张进纸卡纸。
●13.B9.A3
从纸盘3打印时检测到重张进纸卡纸。
●13.B9.A4
ZHCN故障排除工具227
从纸盘4打印时，检测到多页进纸卡纸。
●13.B9.AD
从双面打印器打印时，检测到重张进纸卡纸。
建议操作
小心：请小心热熔器是热的，如果需要清除热熔器内部和周围的碎屑，请使其冷却。
压力加热组件。
1.打开右上门，然后清除所有卡纸。
2.确保纸张符合HP打印机规格。
3.检查定影器送纸传感器的功能和运动是否正常。
4.确认之前没有卡在定影器中的碎屑或引入或流出定影器的辊子没有碎屑。
5.确认出纸槽辊正在转动。
6.卸下ITB并检查是否有损坏和碎屑。
7.进行Manuel传感器测试，并检查SR9定影器输送传感器。如果发现故障，则更换定影器
集会。
8.进行Manuel传感器测试并更换定影组件。
9.更换热凝器。
--------------------------------------------------
英文解释：
13.B9.Az Fuser jam
Description
Fuser delivery stay.
Media stay jam at fuser area.
Paper present at SR9 after specified time limit.
This jam code may be caused by;
An accordion jam at the fuser exit, something blocking the media before the output rollers. The output bin
rollers not turning, there is very little distance from the fuser exit and the output bin.
A sticky fuser exit flag, if it stuck or even delayed momentarily in the activated position.
● 13.B9.A1
Multi-Feed jam is detected when printing from Tray 1.
● 13.B9.A2
Multi-Feed jam is detected when printing from Tray 2.
● 13.B9.A3
Multi-Feed jam is detected when printing from Tray 3.
● 13.B9.A4
ENWW Tools for troubleshooting 227
Downloaded from www.Manualslib.com manuals search engine
Multi-Feed jam is detected when printing from Tray 4.
● 13.B9.AD
Multi-Feed jam is detected when printing from the Duplexer.
Recommended action
CAUTION: Be careful the fuser is HOT, allow it cool if you need to remove debris from in and around the
pressure heating components.
1. Open the upper right door and then clear any jammed paper.
2. Ensure sure that the paper meets HP printer specifications.
3. Check Fuser delivery sensor for proper functionality and movement.
4. verify there is no debris from a previous jam stuck in the fuser or rollers leading into or out of the fuser.
5. Confirm the output bin rollers are turning.
6. Remove the ITB and inspect it for damage and debris.
7. Perform Manuel Sensor Test and check SR9 Fuser delivery sensor. If found faulty then replace the Fuser
assembly.
8. Perform Manuel Sensor Test and Replace the fuser assembly.
9. Replace the fuser.
Description
Fuser delivery stay.
Media stay jam at fuser area.
Paper present at SR9 after specified time limit.
This jam code may be caused by;
An accordion jam at the fuser exit, something blocking the media before the output rollers. The output bin
rollers not turning, there is very little distance from the fuser exit and the output bin.
A sticky fuser exit flag, if it stuck or even delayed momentarily in the activated position.
● 13.B9.A1
Multi-Feed jam is detected when printing from Tray 1.
● 13.B9.A2
Multi-Feed jam is detected when printing from Tray 2.
● 13.B9.A3
Multi-Feed jam is detected when printing from Tray 3.
● 13.B9.A4
ENWW Tools for troubleshooting 227
Downloaded from www.Manualslib.com manuals search engine
Multi-Feed jam is detected when printing from Tray 4.
● 13.B9.AD
Multi-Feed jam is detected when printing from the Duplexer.
Recommended action
CAUTION: Be careful the fuser is HOT, allow it cool if you need to remove debris from in and around the
pressure heating components.
1. Open the upper right door and then clear any jammed paper.
2. Ensure sure that the paper meets HP printer specifications.
3. Check Fuser delivery sensor for proper functionality and movement.
4. verify there is no debris from a previous jam stuck in the fuser or rollers leading into or out of the fuser.
5. Confirm the output bin rollers are turning.
6. Remove the ITB and inspect it for damage and debris.
7. Perform Manuel Sensor Test and check SR9 Fuser delivery sensor. If found faulty then replace the Fuser
assembly.
8. Perform Manuel Sensor Test and Replace the fuser assembly.
9. Replace the fuser.
--------------------------------------------------
实际故障案例
3】故障案例：
--------------------------------------------------
2】故障案例：
--------------------------------------------------
1】故障案例：
扫描开通重新登录查看更多
添加朱师傅微信咨询
