错误代码： 54.14.00 | 惠普5系激光打印机 故障代码 其他系列也可以参考 | 二〇二一年五月二十七日
2021-06-01
--------------------------------------------------
技术热线：朱师傅整理
--------------------------------------------------
中文译本：
54.14.00（仅活动日志）
描述
CPR传感器异常警告
建议操作
1.关闭打印机，然后再打开。
2.使用压缩空气，软刷或碳粉布清洁打印机上多余的碳粉积聚。
3.检查ITB是否损坏，并在必要时进行更换。
266第2章解决问题ZHCN
从www.Manualslib.com手册搜索引擎下载4。确保RD传感器未被墨粉或纸屑污染。用以下方法清洁传感器
压缩空气和软刷。
注意：要清洁密度传感器，请打开右前门和前门，然后卸下定影器和ITB。
关闭前门，露出密度传感器以进行清洁。
图2-83前后浓度传感器
1 2
描述
CPR传感器异常警告
建议操作
1.关闭打印机，然后再打开。
2.使用压缩空气，软刷或碳粉布清洁打印机上多余的碳粉积聚。
3.检查ITB是否损坏，并在必要时进行更换。
266第2章解决问题ZHCN
从www.Manualslib.com手册搜索引擎下载4。确保RD传感器未被墨粉或纸屑污染。用以下方法清洁传感器
压缩空气和软刷。
注意：要清洁密度传感器，请打开右前门和前门，然后卸下定影器和ITB。
关闭前门，露出密度传感器以进行清洁。
图2-83前后浓度传感器
1 2
5.更换ITB组件。
--------------------------------------------------
英文解释：
54.14.00 (EVENT LOG
ONLY)
Description
CPR sensor abnormality warning
Recommended action
1. Turn the printer off, and then on.
2. Clean any excess toner accumulation on the printer using compressed air, soft brush or toner cloth.
3. Check the ITB for damage and replace if necessary.
266 Chapter 2 Solve problems ENWW
Downloaded from www.Manualslib.com manuals search engine
4. Make sure the RD sensor is not contaminated with toner or paper dust. Clean the sensor with
compressed air and soft brush.
NOTE: To clean the density sensors open right and front doors and remove both the Fuser and ITB.
Close front door to expose the density sensors for cleaning.
Figure 2-83 Front and Rear Density Sensors
1 2
5. Replace the ITB assembly.
Description
CPR sensor abnormality warning
Recommended action
1. Turn the printer off, and then on.
2. Clean any excess toner accumulation on the printer using compressed air, soft brush or toner cloth.
3. Check the ITB for damage and replace if necessary.
266 Chapter 2 Solve problems ENWW
Downloaded from www.Manualslib.com manuals search engine
4. Make sure the RD sensor is not contaminated with toner or paper dust. Clean the sensor with
compressed air and soft brush.
NOTE: To clean the density sensors open right and front doors and remove both the Fuser and ITB.
Close front door to expose the density sensors for cleaning.
Figure 2-83 Front and Rear Density Sensors
1 2
5. Replace the ITB assembly.
--------------------------------------------------
实际故障案例
3】故障案例：
--------------------------------------------------
2】故障案例：
--------------------------------------------------
1】故障案例：
扫描开通重新登录查看更多
添加朱师傅微信咨询
